How to Clean Zojirushi Water Boiler

Japan’s Zojirushi water boiler is one of the best selling water heating devices on the market. It gains popularity by homeowners due to the functional design and output water quality. When receiving water, you need to press the lock to release it, and then press the water, then the water will flow out. This design does not require any high-tech, but it plays a very good role in safety protection. When you receive a glass of water for 10 seconds, the water outlet function will automatically lock.

If you have children, the Zojirushi water boiler is the one product I highly recommend, as it outputs the purely safe water. However, because the raw water quality is widely varied, so you might find the water tank might be accumulated a layer of water scales. Therefore, you need to clean up the Zojirushi water boiler regularly.

How to Clean and Care Zojirushi Water Boiler Properly?

If the water in your area is hard or as high in mineral content, you may notice calcium buildup inside your water boiler. This is easily removed with citric acid. Thanks to the interior’s nonstick coating.

Before cleaning, make sure that the filter at the bottom is attached properly so that calcium residue doesn’t get sucked into the pump. Then we mix the cleaning solution by dissolving the citric acid in a cup of warm water, pour it into the boiler and fill with water to maximum level press and hold the reboil button and the light starts to blink. After the cleaning cycle ends, you can remove the lid by pressing the detach button on the back.

You should use it with caution because the water and the inside of the lid will be hot pour the water out from the drain area where marked. Just be sure not to get water inside the control panel or onto the LCD display to rinse fill with clean water and boil again dispense some to rinse out the system and dispose of the rest to clean the outside wipe with a clean cloth.

After repeated use, the gasket may become old and turn white. If it does, you should replace it by calling Zojirushi customer service to purchase a replacement gasket when filling with water or doing any type of cleaning, be careful not to let the bottom get wet, otherwise, it might harm the electrical components of the boiler.

How to Clean Zojirushi Water Boiler with Citric Acid?

  • Firstly, pour 1 sachet of 30g citric acid into a container of warm water, stir until getting dissolved;
  • Pour it into the container and add cold water to the full under the MAX line;
  • Plugin the power to start the automatic citric acid cleaning function. The process takes about 1 to 3 hours;
  • Press the “water supply” button to pour out a glass of water to clean the water outlet pipe. Then unplug the plug and pour out the hot water;
  • Add cold water to the MAX volume, and pour out a cup of water, clean the outlet pipe, then pour out the remaining hot water. The cleaning is completed.

You should adjust the citric acid dosage and holding time according to the degree of fouling.

The discoloration of the inner container caused by the empty heating can’t be removed.

For those models with inner container net, please install the container net first before cleaning.

It is recommended to use citric acid from Zojirushi to clean the water boiler pot. It is also recommended to clean the pot boiler once every 1 to 3 months, so as to remove smelly and dirty scale constantly.

How to remove the water scale in the Zojirushi water boiler?

If your Zojirushi water boiler is blocked and can’t release the water, you need to find a way to remove the water scale accumulated inside. The water scale is mostly caused by too hard water that is not suitable for this precious boiler. There are many different methods to dissolve and remove scale from the boiler inside.

There are white residues on the inner wall of the Zojirushi water boiler after heating. This is not the reason for the Zojirushi boiler. This is the case when the kettle is used for a long time or the electric heater is used for a long time. The white residue produced is scale. Some of the fungicides used in the water plant have not been cleaned, and there are some calcium and magnesium ions in the water, which precipitate out of the water at high temperatures and adhere to the surface of the kettle. You only need to use a small amount of vinegar to clean it, don’t worry

A small amount of scale can be boiled away with white vinegar. If it is thick, go to the supermarket to buy a descaling agent. Some descaling powder or potion can work effectively to dissolve the scale.

We also recommend using edible vinegar (white vinegar is sufficient), shake it evenly for a few minutes, add warm water, and soak for a period of time. It will fall off quickly.

How long does it take to clean the Zojirushi water boiler with citric acid? You can press and hold the boil button until the display flashes, then enter the cleaning mode to start cleaning. The cleaning is completed in about 90 minutes.

Frequently Asked Questions on Zojirushi Water Hot Boiler

If you are using the Zojirushi water boiler, you should check the following questions frequently asked by other users. Just return to refer to these solutions if you have these problems in the future.

Why does My Zojirushi boiler pot have the water scale every day?

This is a water quality problem, and it is normal. It has nothing to do with the Zojirushi electric water boiler. In this case, you should keep cleaning the boiler tank as often as possible. The tap water should be simply filtered and disinfected.

What’s wrong with the paint on the inner tank?

It is a product quality problem, and the paint on the inner tank is not allowed or impossible.

I bought the Zojirushi pot and tried it with a magnet today, but the inner wall can be sucked. Is this normal?

It depends on the stainless steel material. To be precise, it is the content of iron and nickel in the stainless steel. In particular, nickel is an important parameter for the quality of stainless steel. Of course, it is also one of the important factors that determine the price. The content of nickel is high, and it can be absorbed by magnets, just like the stainless steel pot used in induction cookers. If there is no magnetism, It can’t be used. You can try the stainless steel pot special for the induction cooker. If you want a big brand, it must have a good magnetic absorption ability.

Leave a Comment